Smart Meter eMMC5.1 3000 P/E Cycles Data Logger Chip 64GB 128GB 256GB BGA153
Product Summary
Product Details
Smart Meter eMMC5.1 Data Logger Chip
,3000 P/E Cycles Industrial Endurance
,Wide Temperature Embedded Flash Memory
Product Description
Smart Meter eMMC5.1 Data Logger Chip for Utility Metering Terminals
Electricity meters and data concentrators are specified for a fifteen year field life, yet many fail in year six because the embedded storage was borrowed from a consumer phone bill of materials. This Smart Meter eMMC5.1 data logger chip was selected for the opposite duty cycle: small synchronous writes every fifteen minutes, a firmware image rewritten during OTA campaigns, and thousands of unplanned power cuts. The industrial grade stack combines a high performance LDPC controller with 3D TLC NAND, rated at 3000 P/E cycles and ten years of data retention at 55C.
Our metering customers run pilot builds before they release a tender, and the results they care about are retention after repeated power interruption, not peak benchmark numbers. We report both, and we publish the test conditions with the shipment.
Verified Technical Specification
| Model | Capacity | P/E Cycles | Read / Write | Operating Temp | Package |
|---|---|---|---|---|---|
| G2832GTLCA | 32GB | ≥3000 | 330 / 240MB/s | -40C to +85C | BGA 153 |
| G2864GTLIA | 64GB | ≥3000 | 330 / 240MB/s | -40C to +85C | BGA 153 |
| G28128TLIA | 128GB | ≥3000 | 330 / 240MB/s | -40C to +85C | BGA 153 |
| G28256TLIA | 256GB | ≥3000 | 330 / 240MB/s | -40C to +85C | BGA 153 |
Retention figure is measured after 3000 P/E cycling at 55C ambient. NAND configured as 3D TLC with LDPC error correction, 1.8V I/O, HS400 timing, backward compatible with HS200. 32GB uses G2832GTLCA, 64GB uses G2864GTLIA, 128GB uses G28128TLIA and 256GB uses G28256TLIA.
Where This Smart Meter eMMC5.1 Data Logger Chip Is Deployed
- AMI electricity meters. Fifteen minute interval logging and load profiles fit comfortably inside 64GB with decade-long headroom.
- Data concentrators. Local buffering for hundreds of meters when the backhaul link drops, with orderly recovery once the link returns.
- Distribution terminal units. Event logs, fault records and waveform snapshots survive the substation power cycling that follows a fault trip.
- Charging pile controllers. Transaction records persist through contactor switching noise and unscheduled outages.
- Gas and water gateways. Low write frequency, long retention, and a package that tolerates outdoor cabinet temperature swing.
How We Prove Retention and Endurance
Every production lot is cycled to 3000 P/E, baked at 85C for 500 hours, then read back to confirm retention margin. We also run 10000 unplanned power cuts during active write to verify file system integrity, and log controller error counters before release. Buyers receive the cycling log, retention readback summary, RoHS declarations and a lot-level traceability sheet. Engineering support is available for firmware tuning, and we hold the same wafer source for ten years to protect long-life metering programmes.
Questions Utility Buyers Ask About This Smart Meter eMMC5.1 Data Logger Chip
Q: Why does a meter need 3000 P/E cycles when it writes so little?
A: Firmware updates, event logs and waveform capture cause bursts that concentrate writes in a small region. A 3000 P/E rating with static wear levelling keeps that region healthy for fifteen years of OTA campaigns.
Q: What happens if power is cut while the meter writes a firmware image?
A: In-flight cache is flushed on reset and the previous mapping table is restored, so the device reappears on the bus with a mountable file system instead of a corrupted image.
Q: Can the device be configured as pSLC for higher endurance?
A: Our pSLC parts are a separate family (G2808GPLIA to G2816GPLIA for 8GB to 16GB industrial grade). For a TLC device in this series we instead recommend a reserved logging partition with static wear levelling, and we supply the configuration guide.
Q: Which capacity covers a ten year logging profile?
A: A 15 minute interval profile with daily load curves and event logs typically stays inside 32GB (G2832GTLCA). Projects expecting firmware payload growth should step up to 64GB (G2864GTLIA) on the same footprint.
Q: How do you guarantee a ten-year supply for a metering programme?
A: We lock the NAND wafer source and controller firmware revision at project start and commit to a ten-year supply window, with annual buffer stock held for approved customers.
Share your logging interval, memory budget and tender schedule and our metering team will propose a matching capacity and sample plan within one working day.